Moog Minitaur Provozní pokyny stáhnout pdf (Strana 18)

CV MAPPING

In Firmware v2.0 and above, the PITCH, VOLUME, and GATE Controller Inputs on Minitaur can be re-mapped to control other

parameters. This allows you to use voltage control in new and creative ways.

The PITCH and VOLUME inputs provide continuous control, like the panel knobs, while the GATE input only provides on/off

type control. Therefore, the PITCH and VOLUME inputs can be re-mapped to any parameter, while the GATE Input can only

be used to control two-state parameters (on or off).

CV Mapping is configured in the Minitaur Editor/Librarian software on the Hardware Settings panel (Ctrl/command+3 to

display). There is a CV Mapping menu for PITCH, VOLUME, and GATE. Simply click any item on these menus to select a

new destination.

NOTE: CV Mapping settings are global; they do not change per preset and are saved on power down. To reset all Controller

Inputs to default settings, simply click the Default Mappings button on the Minitaur Editor Hardware Settings panel.

CV TO MIDI CONVERSION

Minitaur can now convert multiple channels of Control Voltage to MIDI! This allows you to take CV sources such as modular

synths, a CP-251 Control Processor or a Moog Etherwave Pro theremin, and translate the voltage into MIDI control for your

plug-in effects, soft synths, or other MIDI gear.

All Minitaur sound parameters have an assigned MIDI CC number. When a parameter value changes, Minitaur sends out

MIDI CC data over its USB MIDI connection. When one of the Controller Inputs is mapped to a non-default parameter,

Minitaur will send out CC messages for that parameter in response to control voltage changes at the input.

In order to get optimal response from the CV to MIDI conversion, you will need to adjust the scale and range of the control

voltage to stay within the range of 0 to +5 Volts, before applying voltage to the Controller Input.

WARNING: Do not apply a negative control voltage, or a CV greater than +5 Volts!!

CUSTOM TUNING SCALES

Minitaur now supports the MIDI Tuning Standard (custom tuning scales via MIDI SysEx); documentation is available at

http://www.midi.org/techspecs/midituning.php (Scale/Octave 1-byte and 2-byte forms are supported).

MOOG MINITAUR FIRMWARE v2.1 ADDENDUM

NEW GLOBAL SETTINGS

A number of new global settings have been added to the Minitaur. All global settings can be configured on the Settings page of the v3 Minitaur Editor.

• MIDI Note Transpose allows you to transpose incoming MIDI notes by up to 2 octaves up or down, in increments of 1 semitone.

• MIDI CC Filter allows you to filter out incoming MIDI CC messages, so that the Minitaur responds only to MIDI notes and pitch bend.

• Load Preset Volume: MIDI CC7 sets a volume scale, prior to the (always-active) VCA Volume pot on the front panel. You can now choose to load this

saved volume scale when loading presets. This is OFF by default.

• Load Preset Mod Wheel: You can also load a saved Mod Wheel value per preset; this is OFF by default.

• Poly Voice Number / Max: You can now “Poly Chain” your Minitaur in combination with up to 16 other Moog synths (Little or Slim Phatty; soon to

include Sub Phatty and Sub 37 as well). Just send the same MIDI notes to all units, set the Poly Voice Max equal to the total number of synths in the

chain, and set each synth to a unique Poly Voice Number. Poly Voice Number = OFF disables poly mode, and is the default setting.

• Program Change Send/Recv: ON by default; you can disable sending or receiving Program Change messages if needed.

ADDITIONAL GLOBAL PARAMETERS AND THEIR DEFAULT VALUES

14 BIT MIDI OUTPUT: OFF, ON / DEFAULT = OFF / NOTE: If on, panel knobs send 14 bit CC data.

DECAY/RELEASE MODE: MODE 1 (Decay/Release are linked) / MODE 2 (Decay/Release independent) / DEFAULT = MODE 1

KNOB MODE: SNAP, PASS-THRU, AND RELATIVE / DEFAULT = RELATIVE

MIDI CHANNEL IN: 1 - 16 / DEFAULT = 1

MIDI CHANNEL OUT: 1 - 16 / DEFAULT = 1

KEYBOARD PRIORITY: LOW, HIGH, LAST NOTE, PER-PRESET / DEFAULT = PER-PRESET

CORRECTIONS TO THE MANUAL

TRIGGER MODE - CC 73 (values)

0-42(LEGATO ON),

43-85(LEGATO OFF)

86-127(EG RESET) [was incorrectly given as 85-127 in manual]

KEY PRIORITY - CC 91 (values)

0-42(LOW)

43-85(HIGH)

86-127(LAST) [was incorrectly given as 87-127 in manual]

1 2 ... 13 14 15 16 17 18 19

Komentáře k této Příručce

Žádné komentáře

Moog Minitaur Provozní pokyny Strana 18

Komentáře k této Příručce

Související produkty a manuály pro Syntetizér Moog Minitaur